![]() Some are designed to do repetitive stripping fast, and others are intended for repair work that requires care and versatility. These may seem like simple, standardized hand tools, but there’s actually a few important features that sets one wire stripper apart from another. Manual strippers require you to pull the wire out after the insulation is cut, which can get tiresome if you need to prepare a large number of wires for a project. Many wire strippers will also cut wire, so you don’t need to switch between tools when cutting and stripping numerous lengths of wire at a time.Īutomatic wire strippers make the stripping task quicker by pulling the insulation off the wire as well as cutting it. This is necessary to connect the wire to a terminal or to splice two wires together. The main purpose of wire strippers is to make it simple to remove the plastic insulation from the end of a cut piece of electrical wire. The term “wire stripper” refers to a type of hand tool used by production workers and electricians to assemble and repair wiring. A wire stripper is a must-have tool for anyone who performs wiring work because they make the job of cutting wires and stripping them faster and avoid damaging the metal wire that’s under the insulation. Wire stripping is a task that prepares the end of a wire for a splice or a connection to another electrical component. In this guide we’ve covered wire stripping basics, like how they work and what to look for when buying, as well as reviewed TOP 5 best wire strippers along with their differentiating features. Whether you’re buying your first set of electrician tools or you need to replace a worn-out stripper for home repairs, chances are one of these tools will be right for you. © 2006 - 2020 Gadgets-reviews is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to and affiliated sites.Īre you in need of a new set of wire strippers? You’re in luck because we’ve got a round-up of the best wire strippers available. ![]() □ ALL INFORMATION CLICK HERE □□□□□□īuyer's Guides Reviews More Appliance Gift Ideasĥ Best Wire Strippers for 2021 | Pro Advice to Choose the Best Tools on the Market | Complete Buyer’s Guide The real best way to avoid notches is a thermal stripper but they seem to have gone out of fashion.Automatic Stripper FebruAutomatic Stripper ![]() ![]() Some of the strippers would bend slightly if you squeezed hard so it was difficult to get an adjustment that stripped the insulation cleanly but did not nick the wire. To encourage you to get it right the roving inspectors would check the adjustment of the wiremens strippers – woe betide you if they found notches in the wire. The reason for this was that wires would crack and fail if there were any notches in them. If there were you had to readjust the stripper and try again. The 1cm point was then checked with a strong magnifying glass to see if there was a notch in the wire or any scrape marks to the wire. The same piece of wire was stripped twice – perhaps 1 cm for each. We were taught that stripper and had to adjust them. When I was taught to strip wire by a then Post Office Telephones approved school we had to use the pliers type similar to the more expensive CPC pair in the review. Again works very smoothly one you’ve got it adjusted right. I’ve also got a cable stripper that came bundled as part of a crimp tool set – rather than working in a ‘scissor action’ like all the tools above do, it works by rotating just a single blade all the way around the wire. Seeing how well the phenoptix ones worked, I’m very tempted to buy a pair :) Maybe it’s just because I have a ‘cheap’ version though. I seem to either make the hole too big (so they don’t do a very good job of stripping off the insulation) or I make the hole too small and end up cutting through a bunch of the inner strands as well as the insulation. I’ve currently got a pair similar to the last ones (with thumbscrew) that I think I bought from Maplins, and I always find it really annoying trying to get the adjustment right. That was long before the days when I got to using “digital electronics” gauge wires though. I think the spring on mine eventually failed. They could even be used (with adjustment) to strip both the outer and inner layers of TV coax cable. They worked really well, and the adjustment screw was much longer on mine and IIRC it adjusted the depth of insulation that got cut into. I used to have a pair of the “automatic” strippers when I was little that I bought from a Sunday market (before the days of ebay and cheap chinese knockoffs!). I saw the article title and I assumed it was gong to be another overpriced RS review -)
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |